EC150 CO2/H2O Open-Path Gas Analyzer
Innovative Design
Use as part of open-path eddy-covariance systems or as a stand-alone IRGA
weather applications water applications energy applications gas flux and turbulence applications infrastructure applications soil applications

Overview

Campbell Scientific’s EC150 is an open-path analyzer specifically designed for eddy-covariance flux measurements. As a stand-alone analyzer, it simultaneously measures absolute carbon-dioxide and water-vapor densities, air temperature, and barometric pressure. With the optional CSAT3A sonic anemometer head, the EC150 also measures three-dimensional wind speed and sonic air temperature.


Read More

Benefits and Features

  • New conformal coating helps protect sonic transducers in corrosive environments
  • Unique optical configuration gives a slim aerodynamic shape with minimal wind distortion
  • Analyzer and sonic anemometer measurements are synchronized by a common set of electronics
  • Maximum output rate of 60 Hz with 20 Hz bandwidth
  • Low power consumption; suitable for solar power applications
  • Low noise
  • Measurements are temperature compensated without active heat control
  • Angled windows to shed water and are tolerant to window contamination
  • Field rugged
  • Field serviceable
  • Factory calibrated over wide range of CO2, H2O, pressure, and temperature in all combinations encountered in practice
  • Extensive set of diagnostic parameters
  • Fully compatible with Campbell Scientific dataloggers; field setup, configuration, and field zero and span can be accomplished directly from the datalogger
  • Speed of sound determined from three acoustic paths; corrected for crosswind effects
  • Innovative signal processing and transducer wicks considerably improve performance of the anemometer during precipitation events

EasyFlux® DL is a free CRBasic program for Campbell open-path eddy-covariance systems that is available in the Downloads section. To learn more about EasyFlux® DL, visit the software product's web page.

Images

EC150 gas analyzer head with updated CSAT3A (serial numbers 2000 or greater)
EC150 gas analyzer head with updated CSAT3A (serial numbers 2000 or greater)
EC150 gas analyzer head with updated CSAT3A (serial numbers 2000 or greater)
EC150 gas analyzer head with original CSAT3A (serial numbers less than 2000)
EC150 gas analyzer head
CM250 Boom Adapter
Example open-path eddy-covariance system based on an EC150; large enclosure holds a datalogger and power supply
EC150 gas analyzer head, CSAT3A (serial numbers less than 2000), and EC100 electronics mounted to a mast
Cable ports on bottom of EC100 enclosure
EC150 with CSAT3A (original design, serial numbers less than 2000) and mounting bracket
EC100 enclosure mounting, exploded view
EC150 gas analyzer head and IRGASON & EC150 Zero & Span Shroud mounted on IRGASON & EC150 Lab Stand
EC100 electronics panel
Angled, hydrophobic windows on the EC150 improved performance in rain

Detailed Description

The CSAT3A has the following outputs:

  • Ux (m/s)*
  • Uy (m/s)*
  • Uz (m/s)*
  • Sonic Temperature (°C)*
  • Sonic Diagnostic*

The EC150 has the following outputs:

  • CO2 Density (mg/m3)
  • H2O Density (g/m3)
  • Gas Analyzer Diagnostic
  • Ambient Temperature (°C)
  • Atmospheric Pressure (kPa)
  • CO2 Signal Strength
  • H2O Signal Strength
  • Source Temperature (°C)

*The first five outputs require the CSAT3A Sonic Anemometer Head.

Specifications

Operating Temperature Range -30° to +50°C
Calibrated Pressure Range 70 to 106 kPa
Input Voltage Range 10 to 16 Vdc
Power 5 W (steady state and power up) at 25⁰C
Measurement Rate 60 Hz
Output Bandwidth 5, 10, 12.5, or 20 Hz (user-programmable)
Output Options SDM, RS-485, USB, analog (CO2 and H2O only)
Auxiliary Inputs Air temperature and pressure
Gas Analyzer/Sonic Volume Separation 5.0 cm (2.0 in.)
Warranty 3 years or 17,500 hours of operation (whichever comes first)
Cable Length 3 m (10 ft) from EC150 and CSAT3A to EC100
Weight
  • 2.0 kg (4.4 lb) for EC150 head and cables
  • 1.7 kg (3.7 lb) for CSAT3A head and cables
  • 3.2 kg (7.1 lb) for EC100 electronics

Gas Analyzer
Path Length 15.37 cm (6.05 in.)
A temperature of 20°C and pressure of 101.325 kPa was used to convert mass density to concentration.

Gas Analyzer - CO2 Performance
-NOTE- A temperature of 20°C and pressure of 101.325 kPa was used to convert mass density to concentration.
Accuracy
  • Assumes the following: the gas analyzer was properly zero and spanned using the appropriate standards; CO2 span concentration was 400 ppm; H2O span dewpoint was at 12°C (16.7 ppt); zero/span temperature was 25°C; zero/span pressure was 84 kPa; subsequent measurements made at or near the span concentration; temperature is not more than ±6°C from the zero/span temperature; and ambient temperature is within the gas analyzer operating temperature range.
  • 1% (standard deviation of calibration residuals)
Precision RMS (maximum) 0.2 mg/m3 (0.15 µmol/mol)

Nominal conditions for precision verification test: 25°C, 86 kPa, 400 μmol/mol CO2, 12°C dewpoint, and 20 Hz bandwidth.
Calibrated Range 0 to 1,000 μmol/mol (0 to 3,000 µmol/mole available upon request.)
Zero Drift with Temperature (maximum) ±0.55 mg/m3/°C (±0.3 μmol/mol/°C)
Gain Drift with Temperature (maximum) ±0.1% of reading/°C
Cross Sensitivity (maximum) ±1.1 x 10-4 mol CO2 /mol H2O

Gas Analyzer - H2O Performance
-NOTE- A temperature of 20°C and pressure of 101.325 kPa was used to convert mass density to concentration.
Accuracy
  • Assumes the following: the gas analyzer was properly zero and spanned using the appropriate standards; CO2 span concentration was 400 ppm; H2O span dewpoint was at 12°C (16.7 ppt); zero/span temperature was 25°C; zero/span pressure was 84 kPa; subsequent measurements made at or near the span concentration; temperature is not more than ±6°C from the zero/span temperature; and ambient temperature is within the gas analyzer operating temperature range.
  • 2% (standard deviation of calibration residuals)
Precision RMS (maximum) 0.004 g/m3 mmol/mol (0.006 mmol/mol)

Nominal conditions for precision verification test: 25°C, 86 kPa, 400 μmol/mol CO2, 12°C dewpoint, and 20 Hz bandwidth.
Calibrated Range 0 to 72 mmol/mol (38°C dewpoint)
Zero Drift with Temperature (maximum) ±0.037 g/m3/°C (±0.05 mmol/mol/°C)
Gain Drift with Temperature (maximum) ±0.3% of reading/°C
Cross Sensitivity (maximum) ±0.1 mol H2O/mol CO2

Sonic Anemometer - Accuracy
Offset Error
  • < ±8.0 cm s-1 (for ux, uy)
  • < ±4.0 cm s-1 (for uz)
  • ±0.7° while horizontal wind at 1 m s-1 (for wind direction)
Gain Error
  • < ±2% of reading (for wind vector within ±5° of horizontal)
  • < ±3% of reading (for wind vector within ±10° of horizontal)
  • < ±6% of reading (for wind vector within ±20° of horizontal)
Measurement Precision RMS
  • 1 mm s-1 (for ux, uy)
  • 0.5 mm s-1 (for uz)
  • 0.025°C (for sonic temperature)
  • 0.6° (for wind direction)
Speed of Sound Determined from 3 acoustic paths (corrected for crosswind effects)
Rain Innovative ultrasonic signal processing and user-installable wicks considerably improve the performance of the anemometer under all rain events.

Ambient Temperature
Manufacturer BetaTherm 100K6A1IA
Total Accuracy ±0.15°C (-30°C to +50°C)
EC100 ingress protection IP65

Compatibility

Please note: The following shows notable compatibility information. It is not a comprehensive list of all compatible products.

Dataloggers

Product Compatible Note
CR1000 (retired)
CR1000X
CR300
CR3000 (retired)
CR310
CR350
CR6
CR800 (retired)
CR850 (retired)

Downloads

EasyFlux DL for CR6OP v.2.01 (98.2 KB) 21-07-2022

CR6 datalogger program for Campbell open-path eddy-covariance systems.

View Revision History

ECMon v.1.6 (10.7 MB) 29-03-2016

EC100-Series Support Software.

EC100 OS v.8.02 (560 KB) 14-10-2019

EC100 Operating System.

Watch the Video Tutorial: Updating the EC100 Operating System.

View Revision History

Device Configuration Utility v.2.31 (47.0 MB) 18-12-2024

A software utility used to download operating systems and set up Campbell Scientific hardware. Also will update PakBus Graph and the Network Planner if they have been installed previously by another Campbell Scientific software package.

Supported Operating Systems:

Windows 11 or 10 (Both 32 and 64 bit)

View Revision History

Frequently Asked Questions

Number of FAQs related to EC150: 21

Expand AllCollapse All

  1. When should the enhanced barometer be selected over the basic barometer for the EC150 or IRGASON®?

    Selecting which barometer to use is the choice of the user. There is a direct correlation between the accuracy level of the barometer and its cost.

    • The basic barometer has an accuracy of ±1.5 kPa between 0° and 50°C.  Below 0°, the error increases linearly to ±3.7 kPa at -30°C.
    • The enhanced barometer offers an accuracy of ±0.15 kPa (-30° to +50°C).

    When choosing a barometer, consider the effect of pressure accuracy on flux calculations. For sensible heat flux, the barometric pressure is used to calculate the density of air, which directly scales the sensible heat flux. Therefore, if the barometric pressure measurement is off by 1%, then the sensible heat flux will be off by 1%.

    For CO2 flux, the EC150 and IRGASON® report CO2 as density. Thus, the barometric pressure is not used to directly calculate the flux. However, error in pressure measurements could cause an error in CO2 flux resulting from a CO2 span. During the span procedure, the user enters the “true CO2 value” as a CO2 concentration, which is later converted to density using the barometric pressure. Consequently, the error in CO2 measurements is directly proportional to the error in the barometric pressure measurement.

  2. How often do the windows on the IRGASON® or EC150 need to be cleaned?

    The factory calibration accounts for CO2 and H2O signal strengths down to 0.7. Therefore, to ensure quality data, windows should be cleaned before signal strengths drop below 0.7. 

  3. How can the IRGASON® or EC150 recover more quickly from precipitation, dew, or frost?

    The EC150 and IRGASON® gas analyzer windows are polished, slanted at an angle, and coated with a hydrophobic material to prevent water from collecting on their surfaces. Wicks may also be used on the windows to promote capillary action and move water away from the window edges. Also, heaters in the snouts may be turned on to help minimize data loss because of precipitation and condensation events.

  4. What is the demonstrated wattage for power-up on the IRGASON® or EC150?

    The power requirement for the IRGASON® or EC150 with CSAT3A is 5 W at room temperature regardless of whether it is powering up or under steady-state operation.  At extreme cold or hot temperatures, the power requirement reaches 6 W.

  5. How often should the IRGASON® or EC150 be sent in for recalibration?

    Factory recalibration is done on an as-needed basis. When diagnostic flags begin to appear and persist even after cleaning the analyzer and verifying its settings, a recalibration is needed. Additionally, if the performance of the analyzer has degraded, a recalibration is recommended.  

    One performance test is to check the absolute signal strength drift over the course of 1 year. Drift of a few percent per year is normal. If the annual signal strength drift is excessive, or if the signal strength is below 0.7 when the windows are clean, a factory recalibration is needed. Furthermore, if the ratio of the CO2 to H2O signal strength is not close to one, it may also be time for a factory recalibration. 

  6. Why is a barometer needed for the IRGASON® or the EC150?

    The barometer and temperature sensor are needed because the IRGASON® and EC150 have been calibrated at the factory over a range of temperatures (-30° to +50°C) and barometric pressures (70 to 106 kPa). 

  7. What should the sensor height be for the IRGASON® or EC150?

    The minimum height for the IRGASON® or EC150 should be approximately 2 m. Sensor placement below that height may result in a significant loss in frequency response. The maximum height depends on the available upwind fetch or footprint area.  As a general guideline for unstable boundary layer conditions, the height of the sensor should be less than the distance from the sensor to the outermost edge of the footprint area divided by one hundred. For example, if there is 500 m of available upwind fetch, the IRGASON® or EC150 should not exceed a height of 5 m.  Note that for neutral and stable conditions, the footprint area will grow.

  8. How often do the IRGASON® or EC150 desiccant/CO2 scrubber bottles need to be replaced?

    Campbell Scientific recommends replacing the scrubber bottles yearly. However, if the zero and span coefficients for the CO2 and H2O have drifted excessively, they may need to be replaced more often. 

  9. If getting a span gas is difficult, can the analyzer just be zeroed?

    For greatest accuracy, Campbell Scientific recommends that a zero and a span be done on the EC150 or IRGASON®. However, if a span gas is difficult to obtain, at the minimum, perform a zero on the analyzer.  Performing a zero will correct the majority of drift experienced by the analyzer. Follow the zero procedure in the analyzer’s manual for details.

  10. Can a fine-wire thermocouple be used with the IRGASON® or EC150?

    Yes. A fine-wire thermocouple, such as a FW05, can be used.

Visit the FAQ Library

Case Studies

alaska: eddy covariance
Alaska: Eddy Covariance
Scientists and land-use managers have long recognized the importance of forest lands for their role......read more
Explore All Case Studies

Privacy Policy Update

We've updated our privacy policy.  Learn More